SmallNetBuilder Forums
Go Back   SmallNetBuilder Forums > LAN & WAN > Routers

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 01-10-2013, 03:08 AM
UKEZ UKEZ is offline
New Member
 
Join Date: Apr 2011
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
UKEZ is just starting out
Question Draytek 2850n Open Port Question.

Hiya guys,

I currently have a server plugged up to my Draytek 2850n. I've set up some open ports on my 2850n to enable certain private external servers plotted around internet to communicate with my server via it.

Now my question is, is it possible for me to basically restrict what traffic is allowed in access my routers open ports, then through in to my server?

I hope one of you guys can help...

Last edited by UKEZ; 01-10-2013 at 05:04 AM.
Reply With Quote
  #2  
Old 01-10-2013, 05:00 AM
UKEZ UKEZ is offline
New Member
 
Join Date: Apr 2011
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
UKEZ is just starting out
Question Possible Solution

Okay, so I found this and have configured my my router as suggested.


First I needed need to allow the incoming traffic through the NAT / Open Ports setting (i.e each of the ports you want to open and use).

Next I needed to setup IP Filters, firstly to Block the Open Port you have just created above and then to Pass the specific IP Address(es) you want to allow. I used the Default Data Filter (Set #2) of my Vigor, then his Filter option #2 (ignore the first default rule) and this Block Filter first:

Enable and Name the Filter
Block If No Further Match <--- is the rule I chose
Direction IN --- I used this--> WAN->LAN/RT/VPN was I right?
Protocol <--- in my case I used UDP
Source any <--- left set to any
Destination <--- I set his to my office server IP, was I right to do that?
Destination Start (Ports) <--- added the ports I needed

This apparently makes the Vigor is now pass the incoming traffic through NAT and Blocks it using the above Filter. In the next filter, #3 set up the following:


Pass rule:
Enable and Name the Filter
Pass Immediately <--- I selected this rule
Direction IN --- I used this--> WAN->LAN/RT/VPN was I right?
Protocol <--- in my case I used UDP
Source IP <--- I set this to the remote offsite server IP range, was that right?
Destination IP <-- I set this to my local office server IP and subnet
Destination Start (Port) <--- added the ports I needed

I then click OK. This Pass Filter is now supposedly passing incoming traffic from the Trusted IP/Server on the Internet to the internal Server IP in my office at the required Port.


The original source for this was from an outdated Dratek page... Please feel free to correct my if you think I've done it wrong....


Thanks

Last edited by UKEZ; 01-10-2013 at 05:08 AM.
Reply With Quote
Reply

Tags
2850, filter, open, ports, secure

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


All times are GMT -4. The time now is 02:49 AM.


Top 10 Stats
Top Posters* Top Thanked
RMerlin  393
azazel1024  126
L&LD  120
john9527  97
htismaqe  96
stevech  83
ColinTaylor  77
hggomes  54
sfx2000  51
Anzaia  46
RMerlin  6295
john9527  462
stevech  353
ryzhov_al  290
TeHashX  253
L&LD  244
RogerSC  204
sinshiva  146
sfx2000  136
joegreat  127
Most Viewed Threads* Hottest Threads*
Old Asuswrt-Merli...  58493
Old RT-AC68 -...  25483
Old Moderate Nat...  5525
Old ASUS RT-N66U...  5085
Old iOS 8.1...  4262
Old RT-AC87U -...  2838
Old New AC68...  2481
Old RT-AC68P QOS...  2307
Old AC68U,...  2165
Old Ruckus...  1942
Old Asuswrt-Merli...  253
Old RT-AC68 -...  141
Old Review: 24...  35
Old Moderate Nat...  34
Old iOS 8.1...  33
Old RT-AC87U -...  26
Old RT-AC68P QOS...  24
Old How to flash...  24
Old Linksys...  21
Old Help Plz:...  21


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
© 2006-2014 Pudai LLC All Rights Reserved.