SmallNetBuilder Forums
Go Back   SmallNetBuilder Forums > LAN & WAN > Routers

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 01-10-2013, 02:08 AM
UKEZ UKEZ is offline
New Member
 
Join Date: Apr 2011
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
UKEZ is just starting out
Question Draytek 2850n Open Port Question.

Hiya guys,

I currently have a server plugged up to my Draytek 2850n. I've set up some open ports on my 2850n to enable certain private external servers plotted around internet to communicate with my server via it.

Now my question is, is it possible for me to basically restrict what traffic is allowed in access my routers open ports, then through in to my server?

I hope one of you guys can help...

Last edited by UKEZ; 01-10-2013 at 04:04 AM.
Reply With Quote
  #2  
Old 01-10-2013, 04:00 AM
UKEZ UKEZ is offline
New Member
 
Join Date: Apr 2011
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
UKEZ is just starting out
Question Possible Solution

Okay, so I found this and have configured my my router as suggested.


First I needed need to allow the incoming traffic through the NAT / Open Ports setting (i.e each of the ports you want to open and use).

Next I needed to setup IP Filters, firstly to Block the Open Port you have just created above and then to Pass the specific IP Address(es) you want to allow. I used the Default Data Filter (Set #2) of my Vigor, then his Filter option #2 (ignore the first default rule) and this Block Filter first:

Enable and Name the Filter
Block If No Further Match <--- is the rule I chose
Direction IN --- I used this--> WAN->LAN/RT/VPN was I right?
Protocol <--- in my case I used UDP
Source any <--- left set to any
Destination <--- I set his to my office server IP, was I right to do that?
Destination Start (Ports) <--- added the ports I needed

This apparently makes the Vigor is now pass the incoming traffic through NAT and Blocks it using the above Filter. In the next filter, #3 set up the following:


Pass rule:
Enable and Name the Filter
Pass Immediately <--- I selected this rule
Direction IN --- I used this--> WAN->LAN/RT/VPN was I right?
Protocol <--- in my case I used UDP
Source IP <--- I set this to the remote offsite server IP range, was that right?
Destination IP <-- I set this to my local office server IP and subnet
Destination Start (Port) <--- added the ports I needed

I then click OK. This Pass Filter is now supposedly passing incoming traffic from the Trusted IP/Server on the Internet to the internal Server IP in my office at the required Port.


The original source for this was from an outdated Dratek page... Please feel free to correct my if you think I've done it wrong....


Thanks

Last edited by UKEZ; 01-10-2013 at 04:08 AM.
Reply With Quote
Reply

Tags
2850, filter, open, ports, secure

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


All times are GMT -4. The time now is 02:29 PM.


Top 10 Stats
Top Posters* Top Thanked
RMerlin  365
stevech  156
KGB7  124
Kel-L  98
sfx2000  98
sinshiva  93
azazel1024  93
john9527  75
fistv  71
hggomes  68
RMerlin  5597
stevech  329
ryzhov_al  266
TeHashX  217
L&LD  191
RogerSC  190
sinshiva  143
joegreat  127
jlake  122
sfx2000  121
Most Viewed Threads* Hottest Threads*
Old Asuswrt-Merli...  77974
Old Asuswrt-Merli...  45893
Old [Fork]...  19676
Old Asus locking...  10291
Old ASUS...  8260
Old Incoming...  8009
Old Share What...  3870
Old Asuswrt-Merli...  3341
Old Asuswrt-Merli...  3017
Old Ac68u Latest...  2664
Old Asuswrt-Merli...  393
Old Asuswrt-Merli...  206
Old [Fork]...  134
Old Asus locking...  125
Old Connection...  54
Old [HOW TO]...  50
Old ASUS...  49
Old Incoming...  44
Old 376.44 -...  40
Old Use the same...  35


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
© 2006-2014 Pudai LLC All Rights Reserved.