SmallNetBuilder Forums
Go Back   SmallNetBuilder Forums > LAN & WAN > Routers

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 01-10-2013, 02:08 AM
UKEZ UKEZ is offline
New Member
 
Join Date: Apr 2011
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
UKEZ is just starting out
Question Draytek 2850n Open Port Question.

Hiya guys,

I currently have a server plugged up to my Draytek 2850n. I've set up some open ports on my 2850n to enable certain private external servers plotted around internet to communicate with my server via it.

Now my question is, is it possible for me to basically restrict what traffic is allowed in access my routers open ports, then through in to my server?

I hope one of you guys can help...

Last edited by UKEZ; 01-10-2013 at 04:04 AM.
Reply With Quote
  #2  
Old 01-10-2013, 04:00 AM
UKEZ UKEZ is offline
New Member
 
Join Date: Apr 2011
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
UKEZ is just starting out
Question Possible Solution

Okay, so I found this and have configured my my router as suggested.


First I needed need to allow the incoming traffic through the NAT / Open Ports setting (i.e each of the ports you want to open and use).

Next I needed to setup IP Filters, firstly to Block the Open Port you have just created above and then to Pass the specific IP Address(es) you want to allow. I used the Default Data Filter (Set #2) of my Vigor, then his Filter option #2 (ignore the first default rule) and this Block Filter first:

Enable and Name the Filter
Block If No Further Match <--- is the rule I chose
Direction IN --- I used this--> WAN->LAN/RT/VPN was I right?
Protocol <--- in my case I used UDP
Source any <--- left set to any
Destination <--- I set his to my office server IP, was I right to do that?
Destination Start (Ports) <--- added the ports I needed

This apparently makes the Vigor is now pass the incoming traffic through NAT and Blocks it using the above Filter. In the next filter, #3 set up the following:


Pass rule:
Enable and Name the Filter
Pass Immediately <--- I selected this rule
Direction IN --- I used this--> WAN->LAN/RT/VPN was I right?
Protocol <--- in my case I used UDP
Source IP <--- I set this to the remote offsite server IP range, was that right?
Destination IP <-- I set this to my local office server IP and subnet
Destination Start (Port) <--- added the ports I needed

I then click OK. This Pass Filter is now supposedly passing incoming traffic from the Trusted IP/Server on the Internet to the internal Server IP in my office at the required Port.


The original source for this was from an outdated Dratek page... Please feel free to correct my if you think I've done it wrong....


Thanks

Last edited by UKEZ; 01-10-2013 at 04:08 AM.
Reply With Quote
Reply

Tags
2850, filter, open, ports, secure

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


All times are GMT -4. The time now is 07:16 AM.


Top 10 Stats
Top Posters* Top Thanked
RMerlin  323
L&LD  137
john9527  137
stevech  117
azazel1024  115
htismaqe  91
sfx2000  75
ChristineBCW  75
TonyH  68
AndreyPopov  55
RMerlin  6000
john9527  367
stevech  348
ryzhov_al  277
TeHashX  230
L&LD  230
RogerSC  199
sinshiva  147
sfx2000  132
joegreat  126
Most Viewed Threads* Hottest Threads*
Old Asuswrt-Merli...  73093
Old Shellshock...  27194
Old Asuswrt-Merli...  3714
Old Antenna...  3662
Old Asus...  3310
Old Simple NAS...  2225
Old Brainstorming...  2026
Old Looking for...  1793
Old RT-AC68P  1489
Old New Router:...  1481
Old Asuswrt-Merli...  314
Old Antenna...  73
Old Brainstorming...  47
Old Simple NAS...  36
Old Looking for...  35
Old Asuswrt-Merli...  34
Old Shellshock...  31
Old Asus...  29
Old WiFi Rates  23
Old Issues...  22


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
© 2006-2014 Pudai LLC All Rights Reserved.