SmallNetBuilder Forums
Go Back   SmallNetBuilder Forums > Wireless Networking > Wireless Buying Advice

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 01-17-2013, 04:48 PM
dollarbill dollarbill is offline
New Member
 
Join Date: Jan 2013
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
dollarbill is just starting out
Default Help! Can't Decide! And some basics Q's.

Sorry this is so long... I'm confused.
I have delved deep into the router charts and poured over the reviews. I still can't decide. I have fairly simple needs, but there are some things I just don't understand.

My setup:
Paying for RCN 50Mbps. We have a couple lap-tops and 2 iphones that need the wireless signal. They are all wireless N devices.

My situation:
I have a Cisco e1200 that works fine for a few hours and then the speeds deteriorate. When I jack straight into the modem and hit up speedtest.net I'll see 50Mbps. When I reset the router I'll see between 30 - 50mbps in the same room and between 15 - 40mbps on the other side of the apartment. Like I said... a couple hours later and I'm getting between 1 - 10 Mbps and everything has to get reset.

My guess is that the RAM is getting full on my router and resetting it is clearing it out. Does that make sense?

The charts have me freaked out because I see a number like 31.1 (which is what my e1200 gets in the 2.4ghz-throughput-down test) and that's lower than the 50Mbps that's coming into the house. Yet when I'm connected to wireless I can pull 50Mbps easy. So obviously there's something I don't understand about the tests. What gives?

I want to spend as little as possible, and I just need stability and something that will allow me to take advantage of the 50mbps speeds that I'm paying for. EDIT -- I guess I don't even need gigabit ports considering speed of the feed coming in.

Is the Cisco-e4200/Asus-u56n level overkill? I don't think I need the 5ghz band, so would the Belkin-F9K1103 work? Could I go even cheaper than those while maintaining stability (not resetting everything every day) and without wasting money on 50Mbps cable feed?

Last edited by dollarbill; 01-17-2013 at 08:19 PM.
Reply With Quote
  #2  
Old 01-17-2013, 09:27 PM
sfx2000 sfx2000 is offline
Very Senior Member
 
Join Date: Aug 2011
Location: San Diego, CA
Posts: 1,228
Thanks: 16
Thanked 134 Times in 120 Posts
sfx2000 is just starting out
Default

The E1200 is a fine single-band 2 steam router.

Couple of things - Linksys (by Cisco) has had issues in the past with their uPNP stack, so try disabling uPNP.

Looking at the E1200 firmware release notes for the V2 variants, there were some performance issues that have been resolved with the most recent firmware, so check that as well.

do this first before throwing money at new hardware...

sfx
Reply With Quote
  #3  
Old 01-17-2013, 10:30 PM
stevech stevech is offline
Very Senior Member
 
Join Date: Mar 2010
Location: San Diego
Posts: 4,852
Thanks: 1
Thanked 352 Times in 340 Posts
stevech is just starting out
Default

WiFi throughput (data speeds) will vary 2:1 or more in a short time.
Long term, it'll average out. Such is wireless.
The exception is if you have an air-time hoggy neighbor and if so, to escape, just change to another channel (in 2.4GHz, that's 1, 6 or 11).
Reply With Quote
  #4  
Old 01-17-2013, 11:56 PM
dollarbill dollarbill is offline
New Member
 
Join Date: Jan 2013
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
dollarbill is just starting out
Default

I'm already on Channel 6. The router I have is the e1200 v1 and I upgraded to the latest firmware (1.0.3) when I started seeing problems. Thanks for the tip about upnp. I'll give that a shot for a couple days.

I didn't have a router when I signed up for this internet service so I thought I'd lease the one they provide while I looked for the right one to buy.

So I still need to get one. It sounds like you're saying I could just snag an e1200 or anything comparable?
Reply With Quote
  #5  
Old 01-18-2013, 12:27 PM
stevech stevech is offline
Very Senior Member
 
Join Date: Mar 2010
Location: San Diego
Posts: 4,852
Thanks: 1
Thanked 352 Times in 340 Posts
stevech is just starting out
Default

Quote:
Originally Posted by dollarbill View Post
I'm already on Channel 6.
There are simple things you can do to determine if channel 6 plus/minus neighbor-channels is frequently overburdened with neighbors' streaming files/videos, to your disadvantage.
Reply With Quote
  #6  
Old 01-18-2013, 02:39 PM
thiggins's Avatar
thiggins thiggins is offline
Mr. Easy
 
Join Date: May 2008
Posts: 9,189
Thanks: 165
Thanked 629 Times in 533 Posts
thiggins is just starting out
Default

The 31.1 Mbps you refer to is an average of all test locations. To see the individual location results use the Throughput vs. location button or the view selector up next to the benchmark selector.
__________________
Tim Higgins
Managing Editor,SmallNetBuilder.com
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -4. The time now is 11:54 AM.


Top 10 Stats
Top Posters* Top Thanked
RMerlin  402
john9527  157
azazel1024  114
htismaqe  100
sfx2000  81
stevech  75
ColinTaylor  65
AndreyPopov  57
TonyH  56
bbb0777  42
RMerlin  6059
john9527  389
stevech  351
ryzhov_al  280
TeHashX  237
L&LD  232
RogerSC  201
sinshiva  147
sfx2000  134
joegreat  126
Most Viewed Threads* Hottest Threads*
Old Asuswrt-Merli...  28340
Old Brainstorming...  2626
Old Advice on...  2570
Old Looking for...  2350
Old RT-AC68P...  2277
Old RT-AC68U...  1865
Old Asus...  1794
Old Issues...  1760
Old Stable...  1647
Old AC-68...  1602
Old Asuswrt-Merli...  205
Old Advice on...  49
Old Brainstorming...  47
Old Looking for...  35
Old RT-AC68P...  29
Old WiFi...  27
Old Stable...  25
Old Issues...  25
Old WiFi Rates  23
Old RT-AC68U...  22


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
© 2006-2014 Pudai LLC All Rights Reserved.